How can next-generation, Low-k intermetal dielectrics be tuned to meet customer’s specific integration requirements?
Low-k Intermetal Dielectrics (ILD) have been used in back-end integration for well over a decade. These films have evolved from dense, single precursor based carbon doped oxides to porous, structure former and porogen based carbon doped oxides, or porous Low-k films. The addition of porosity was necessary to reduce k between 2.5–2.6, which is the typical porous Low-k films currently in HVM.
As film pitches have shrunk with technology node advancements, the demands put upon Low-k films have evolved. Depending on an Integrated Device Manufacturer’s integration scheme, mechanical properties can become very critical with higher elastic modulus and hardness is required to reduce mechanical defects in very thin ILD layers. Another consideration for thin ILD layers is Plasma Induced Damage (PID) of the ILD film through side wall exposure to the etching and ashing steps during integration, which can impact the electrical performance of the films. PID occurs when reactive radicals strip carbon from the film leaving reactive sites that ultimately get converted to hydroxyl groups and increase the dielectric constant.
In current Low-k process chemistries, these two principals, mechanical strength and PID with subsequent k loss, trend in opposite directions. For a given k value, increasing carbon content of Low-k film reduces the depth of PID by reducing the penetration depth of reactive radicals formed in the plasma. However, higher carbon content films have a lower silicon-oxygen bond density resulting in lower mechanical strength. Conversely, reducing the carbon content to increase mechanical strength requires a higher degree of porosity to maintain the dielectric constant, thereby increasing depth of the plasma damage.
Balancing these needs can be critical to developing a successful ILD process for next generation devices. Versum Materials is developing solutions that can bridge the gap between strong mechanical properties and reduced PID. By controlling the type and amount of carbon deposited into the film, a balance between higher mechanical strength and reduced PID can be achieved. In addition to working with OEMs, Versum Materials can work with individual IDMs to tailor an ILD solution to meet their specific integration needs. Our applications lab is equipped with a state-of-the-art 300mm PECVD process tool that is used to develop Best Known Methods (BKM) that can be readily transferred to HVM process tools.
Versum Materials has designed new structure forming precursors for use with existing porogens, or used alone for very high mechanical strength films, to help meet the evolving film requirements of advanced technology nodes at 10 nm, 7 nm, 5 nm and beyond. A fundamental understanding of how precursor structure impacts film properties in a PECVD process combined with a statistical Design of Experiments (DOE) approach is used to map process conditions such as plasma power, precursor and oxidant flow rates, temperature and pressure. This allows prediction of process parameters required for a precursor to obtain specific film properties. State-of-the-art metrology for measuring film properties including thickness, refractive index, porosity, composition, chemical bonding, dielectric constant and mechanical properties are used. These metrology tools have been benchmarked against external metrology tools including those at OEMs, IDMs and research institutes.
Versum Materials welcomes the opportunity to work with you to discuss and help develop your specific ILD film requirements for next generation devices. Our extensive experience combined with a robust process database can provide a starting point to develop a tailored solution to meet your ILD needs for single precursor dense or porous Low-k ILD.
O’Neil M. L. et al. Optimized Materials Properties for Organosillicate Glasses Produced from Plasma Enhanced Chemical Vapor Deposition, MRS Proceedings, Vol 766, Cambridge Univ Press 2003
Ridgeway R. G. et al. Development of Porous Low-k Precursor to Provide Enhanced Mechanical Properties without Sacrificing Carbon Content, Proceedings Semicon Taiwan, Sep 2016
Robert Ridgeway has worked in electronics technology for the past 27 years. He is currently the group leader of the organosilanes PECVD/FCVD applications development team in Tempe, AZ. Bob graduated from Drexel University with a Ph.D. in chemistry.
In This Section
- Delivery Systems Manuals
- Versum Lab Notes
- How does Versum Materials determine which new molecules to create?
- How does Versum Materials use computational chemistry to accelerate CVD or ALD precursor development?
- What methodology does Versum Materials use to establish thermal stability of CVD and ALD precursors?
- How can next-generation, Low-k intermetal dielectrics be tuned to meet customer’s specific integration requirements?
- Assay means purity, right?
- Why does Versum Materials prefer digestive metal analysis methods for Organometallic Materials (OM)?
- What is the advantage to an all metal sealed container?
- What GASGUARD system is best for controlling heated specialty gases to the tool in my fab?
- How does Versum Materials develop next-generation precursors for their customers?
- How is Versum Materials handling the growing demand for PDMAT for advanced technology nodes?
- How does Versum Materials ‘walk’ the delivery systems ‘safety talk’?
- Customer Resources
- Safety Data Sheets
- Supplier Information